Connect with us

NYBowhunter.com – Bow Hunting Advice and Tips

Hunter Safety Systems Lady Pro – NY Bowhunter

ATA Trade Show

Hunter Safety Systems Lady Pro

Published

on

Treestand safety has been a big thing over the last few years in the hunting industry and for good reason – falls from treestands are the leading cause of hunting related injuries. Safety harnesses should be worn at all times when you’re climbing up to your stand, hunting from a treestand and when climbing down from a treestand.

The new Lady Pro from Hunter Safety Systems is cut to fit a woman’s body providing a comfortable, snug fit which is especially important to bowhunters. The Lady Pro features six pockets, ventilated mesh and a binocular/rangefinder strap just like the men’s version of the safety harness.

The Lady Pro retails for $149.95 and has a maximum chest width of 56 inches and weight capacity of 250 pounds.

I’ve had several close calls with climbing stands where the bottom of the stand fell from the tree and it was my safety harness that kept me from falling to the ground. It’s not just when you’re climbing up a tree that you should be wearing a safety harness. Last season I made the mistake of not wearing a harness while taking down a double set of fixed stands after the season. As I let the two stands down the rope I was using caught onto one of my climbing sticks and pulled it sideways so I couldn’t step on it. I had no harness and had to use the stick I was standing on and the one sick above me to descend the tree. It was a very slow process and my arms and legs began to ache as I climbed down the tree a mere six inches at a time. If I had a safety harness I could have easily climbed down the tree and safely returned to the ground.

Make sure you and your friends are wearing a safety harness on all of your hunts from above.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Girls Can Shoot Too! The PSE X-Force Vendetta XS – NY Bowhunter

ATA Trade Show

Girls Can Shoot Too! The PSE X-Force Vendetta XS

Published

on

The 2011 ATA Show in Indianapolis was an exciting event for me. It was my first time attending the show and I had an opportunity to meet a ton of people that I had worked with previously through NYBowhunter.com. To top it off, I gained first hand knowledge of some of the hottest products to hit the archery market in 2011. But what I didn’t expect was for Jenn, a non-archer, to pick up a bow and start shooting!

Jenn and I visited all the top manufactures booths and she was able to shoot bows by Strothers, Hoyt, PSE and Elite. Everyone we met was eager to help Jenn and get her started while she shot a compound bow for the very first time.

Being at an Archery Trade show the bow manufactures tried to have the most common draw lengths available, but they didn’t have them all. The PSE Vendetta that Jenn was shooting was a little too short for her, but that didn’t stop her from having fun with it!

Jenn was easily able to draw back the Vendetta on her own with the bow set at 40 pounds. With 75% let-off and a mass weight of 3.95 pounds the Vendetta was easy for Jenn to hold at full draw.

We spent quite a bit of time at the PSE booth as Jenn and I were both having fun shooting the bows. Although, I think she enjoyed it a little more than me.

The PSE Vendetta XS is a great bow for women looking to get into archery. With it’s 29 1/2″ axle-to-axle length and light weight it’s an easy bow for a woman to handle and learn the sport of archery.

One thing I thought was pretty cool about the PSE bows was that they’re also available in Skulz Camo as a finish option. The PSE Chaos in Skulz Camo, pictured above, just might make you the coolest kid on the block!

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Elite Archery – Elite Pure vs. Elite Pulse – NY Bowhunter

ATA Trade Show

Elite Archery – Elite Pure vs. Elite Pulse

Published

on

I had a chance to stop by the Elite Archery booth while at the ATA Show this year and take a few shots with all of the bows in their 2011 lineup including the Pure and the Pulse. Elite is known for having fast, smooth bows that are easy to draw and they didn’t disappoint with this years lineup.

First up was the Elite Pure, a 36″ axle-to-axle bow with a 7″ brace height. With these two specs alone, I knew this would be a very forgiving hunting bow, but would it have the speed? Shooting between 326 fps to 330 fps the answer is a resounding YES!

I felt right at home picking up the Pure and wrapping my hand around the slim grip that Elite is known for. This really helps minimize any sort of torque your bow hand would put on the bow and helps you shoot more consistent.

The draw was easy and smooth with a steep valley into the wall – some people don’t care for this, but I really like the feel of it, especially for hunting situations. With over 80% let-off, once you’re at full draw you don’t have to worry about going anywhere. There is no fight in this bow and you can really hold it for comfortably for long periods of time – perfect for when you have to draw on a big buck quickly, but then have to wait for the shot. The down side to this is that it makes it more difficult to let down the bow once you’re at full draw if you decide not to take the shot. You’ll have to slowly ease up while feeling like nothing is happening and then all of a sudden the bow will let down fast – it sounds scary, but once you let the bow down a few times you’ll know what to expect and be able control it.

Both the Pulse and the Pure share the same cam – the EFX. The EFX cam is an incredibly smooth and fast cam with high let-off, making it ideal for hunting. The Pulse is slightly shorter than the Pure with a 34 1/4″ axle-to-axle length, a tad heavier at 4.3 pounds vs. 4.1 pounds for the Pure, and has a 1″ shorter brace height making this bow slightly less forgiving. Is the trade off worth it? That depends, do you like speed? If so, the Pulse will get your heart racing as it launches arrows over 340 fps.

One thing I like about the Elite bows that sometimes goes unnoticed is the flat riser shelf. This ensures that the riser shelf won’t interfere with any type of rest you put on this bow so you’re not limited by what works with the riser shelf.

Elite also partnered with Stokerized Stabilizers, one of the hottest stabilizers on the market, to effectively reduce vibration while at the same time balancing directional forces at full draw – it’s a deadly stabilizer.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Easton Archery Continues to Expand its Line of Products – NY Bowhunter

ATA Trade Show

Easton Archery Continues to Expand its Line of Products

Published

on

Each year archery manufacturers continue to improve and expand upon their line of products and Easton Archery is no different.

Expanding upon the popular Easton A/C/C Superlight arrows, Easton recently introduced the A/C/C Pro Hunter which is quickly becoming the arrow of choice for hardcore bowhunters who demand the highest quality arrow.

Easton also manufactures a wide variety of arrow components such as the Diamond Vane which is available in a variety of sizes to suit the needs of hunters and target archers alike.

With the advent of lighted nocks, Easton has developed the tracer nock that utilizes a magnet placed on the bow shelf to activate the nock as the arrow passes by upon release. Personally, I don’t care for this system as the magnet has a tendancy to pull the arrow head towards the riser.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Elite Hunter and the Elite Tour – NY Bowhunter

ATA Trade Show

Elite Hunter and the Elite Tour

Published

on

The 2011 Elite Hunter is a smooth drawing, short axle-to-axle bow that’s the perfect bow for a first time hunter or seasoned archer. Jenn and I both had a chance to shoot the Elite Hunter at the ATA Show and were both very impressed by how easy this bow was to shoot. The ESX cams are rounder than the EFX cams found on both the Pulse and Pure. The rounder cams provide for an even smoother draw and allow you to easily control the let down of the bow – a plus over the EFX cams on the Pulse and Pure which take a little getting used to when it comes to letting down when you’re at full draw.

NYBowhunter.com testing out the 2011 Elite Hunter

With a 7 1/2″ brace height this bow is very forgiving. Combine that with peak draw weights from 40 to 80 pounds and you have a bow that any archer could shoot.

Jenn with the 2011 Elite Hunter

The Elite Hunter has an axle-to-axle length of 31 3/4″ which makes it perfect for hunting out of a ground blind or treestand. With speeds up to 323 feet per second this bow is now slow shooter. This is a great bow for those who prefer the maneuverability of a shorter axle-to-axle bow. It’s also the perfect bow to get your girlfriend, wife or a youth into the sport of archery.

Marc from NYBowhunter.com takes aim with the 2011 Elite Tour

The Tour is one sweet looking target bow and it has the performance to back it up. The Tour has a 38″ axle-to-axle length and a 7 7/8″ brace height to help you keep it in the 12 ring. The Tour cams are smooth and provide for an easy draw like the rest of the bows in the Elite stable. I felt like I could shoot the Tour all day long and if you’re a serious target archer that’s just the type of bow you want.

Elite definitely left a lasting impression on me at the ATA Show with their 2011 lineup and they continue to push the bar in speed, smoothness and easy to shoot bows. Elite makes one of the few bows that you can pull back to full draw and feel absolutely comfortable holding it there so you can concentrate on picking out a spot on that big buck instead of fighting the bow to keep it at full draw. Next time you’re at your local pro shop make sure you give the Elite lineup a try and feel the difference for yourself.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Bullish Dealers Write Orders, Save Dollars At 2011 ATA Trade Show – NY Bowhunter

ATA Trade Show

Bullish Dealers Write Orders, Save Dollars At 2011 ATA Trade Show

Published

on

INDIANAPOLIS — The 2011 ATA Trade Show attracted a business-ready crowd of more than 8,000 industry professionals last week, with archery and bowhunting manufacturers reporting heavy booth traffic and order-writing.

The annual event — held Jan. 6-8 in the Indianapolis Convention Center — boasted a record-sized Show floor featuring 513 exhibitors who rented 167,550 square feet of space, including a record 55 shooting lanes, 11 more than in 2010. In addition to booth space occupied, there were 2,989 dealers, buyers and distributors on the Show floor during the three-day event. Like last year, the ATA will unpack the Show numbers and release a complete registration report featuring a breakdown of attendance numbers, exhibiting trends and geographic attendance patterns. The report should be finalized later this month.

“It was gratifying to see the strong response of the industry’s dealers, buyers and other folks who came to Indy,” said Jay McAninch, ATA CEO/president. “When every company comes together in one city, under one roof, business opportunities are maximized and the cost of doing business is minimized. The ability of our industry to unite and get to work deserves applause and a thank you to each company represented at the Show this year.”

Bob Miller, owner of BKIII Archery in Waterford, Wisconsin, said dealers truly cannot afford to miss the Show. “The Show has been great for us,” he said. “The amount of money we’re able to save by attending allows us to stay in business.”

One of the broader goals of each Show is to strike a balance between bringing back those Show features that benefit member companies, while allowing the Show to evolve and adjust as industry needs change. This year, attendees relied on the proven online registration platform introduced at the 2010 Show and the ATA express pass kiosks, Big Buck Tags returned to deliver discounts to dealers, while serving as a marketing beacon for participating exhibitors. Meanwhile, for 2011, the ATA introduced the interactive floor plan and directory, You Are Here, and the well received Beer and Gear Exchange.

“I think that’s one of the things the ATA staff and Board always come back to,” said Kurt Bassuener of Mike Wieck Sales. Bassuener also serves as the Trade Show’s committee chair on the ATA Board of Directors. “We can’t get stale, we have to gather feedback, be considerate and thoughtful based on what we hear and act on what we learn. Our industry has always been good to guide and speak up about what they’re after. So the clues were there for us to act on and, based on how our members embraced You Are Here and the sizable crowds at the Beer and Gear Exchange, the Show benefited from member feedback and we’d like to think our members benefited too. Now, the challenge is to refocus, emphasize this approach for 2012 and deliver.”

On the order-writing front, manufacturers at the Show reported increased optimism from archery-shop owners visiting their booths. “We had a lot more dealer traffic in our booth, and in talking with them you sense the economy is rebounding,” said Ben Guttormson, a national account manager with Black Gold. “You sense that if you’re a dealer and you made it through the past couple of years, the sun’s on the horizon. They’re well-organized, know what they want, and they’re here taking advantage of the Show’s deals.”

Brian Park, co-owner and president of Strother Archery, said his company wrote more orders and signed up more dealers than anticipated in their second year at the Show. “We took out a 20-by-30 booth because we had so much traffic last year,” Park said. “We made sure we could accommodate even more dealers this year, and we succeeded.”

Isaac Aleman, sales manager for Badlands Packs, said, “We were constantly busy writing orders. This is one of the better shows for dealers. We picked up some new international accounts and met a lot of Eastern dealers. That’s important for Western companies like ours.”

The deals weren’t a one-way street. Steven Wagnitz, president of Lakewood Products, and Aleman were just two of many exhibitors and retailers who snapped up specially priced hotel rooms the ATA arranged near the convention center.

“ATA’s hotel discounts definitely help,” Wagnitz said. “We stayed right across the street at the Hyatt, and could walk over here without going outside. You can’t beat the price or convenience.”

Lisa Endicott, co-owner of the Bow Rack archery store in Springfield, Ore., said she has learned to book their hotel room as soon as the ATA opens registration. “The rooms go fast and you can see why,” she said. “The ATA rates allow you to stay in hotels that are nicer than what we’d normally stay in. You can’t beat the prices they negotiate. We haven’t even paid for taxis here because we took advantage of the airport shuttles.”

McAninch said the ATA is now focusing on the Show’s return to Columbus, Ohio, Jan. 12-14, 2012. “We’re working hard with the Columbus folks to ensure next year’s Show is just as successful for our members,” he said. “Indianapolis always sets the bar high, and it’s our job to make sure all host cities make the Show pay dividends for our members.”

For more information about the 2011 ATA Trade Show or information about the 2012 ATA Trade Show in Columbus, please call (866) 266-2776 or e-mail info@archerytrade.org.

About the ATA Trade Show: The ATA Trade Show is the archery and bowhunting industry’s largest and most inclusive show. The member-driven event promotes commerce within the industry, and is owned and operated by the ATA. As the only industry show that funds archery and bowhunting growth, the ATA invests in state agencies to coordinate introductory archery initiatives such as National Archery in the Schools Program and the After School Archery Program. To date, the ATA has invested and pledged nearly $2 million to bring archery shooting facilities and introductory programs to U.S. cities. Meanwhile, the ATA also fights for bowhunting rights in courtrooms across the country. The show is closed to the public and is an order-writing event.

About the ATA: Since 1953 ATA has been the trade association for manufacturers, retailers, distributors, sales representatives and others working in the archery and bowhunting industry. ATA is dedicated to making the industry profitable by decreasing business overhead, and reducing taxes and government regulation while increasing participation in archery and bowhunting. ATA owns and manages the ATA Trade Show, the archery and bowhunting industry’s largest and longest running trade show worldwide.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Bowtech Invasion unveiled at 2011 ATA Show – NY Bowhunter

ATA Trade Show

Bowtech Invasion unveiled at 2011 ATA Show

Published

on

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

BowHook Slings Makes it Easy to Carry Your Bow – NY Bowhunter

ATA Trade Show

BowHook Slings Makes it Easy to Carry Your Bow

Published

on

I met the owners of BowHook Sling as I toured the booths in the Innovation Room at the ATA Show. The company is a local company based in south central New York and their product is a simple, yet effective way to free a hunter or target archer’s hands for climbing into a treestand or just pulling arrows from a 3D target.

The BowHook Sling uses a nylon web belt with a leather hub to form the unique “X” shape that separates the hooks from the sling. The rubber coated hooks help dampen the sound of metal on metal, but if the hook hits a metal riser hard enough it will make noise. I used this sling on my Hoyt Carbon Matrix and the unique design of the carbon riser made the BowHook Sling a little more difficult to use, but on standard aluminum risers with uniform cut outs it’s very easy to hook the sling up to the bow and take it off.

The BowHook Sling is available in a wide variety of colors including a variety of target colors, digital camo, pink camo and Realtree AP. Prices range from $15 for black and tan, $25 for target colors, and $30 for the Realtree AP version.

For more information on the BowHook Sling or to purchase visit http://www.bowhookslings.com/.

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending

Axcel Hunting Sights in 3 Camo Patterns – NY Bowhunter

ATA Trade Show

Axcel Hunting Sights in 3 Camo Patterns

Published

on

One of my favorite hunting sights is the Axcel Armourtech HD. This is the toughest sight I’ve ever used and the only thing it was ever lacking was a camo finish option.

New for 2011, Axcel offers it’s Armourtech sights in three camo patterns: Lost Camo, Mossy Oak Infinity and Realtree APG.

The sights remain some of the toughest in the industry and now you can match the camo to your bow!

For those who want greater accuracy down range, T.R.U. Ball also has the Armourtech Pro models which feature an adjustable sight bar, also available in camo.

For target archers there is the new Red Ring Torque Indicator which allows the archer to instantly see if they are torquing the bow. The red ring spacer is behind the pin and in front of the lens. If you’re holding your bow level you won’t see the red ring, but as soon as you torque the bow it appears. This is a great idea and I hope they bring this over to their hunting sights as well.

To keep up with the fast speeds of today’s high tech bows, Axcel offers a High Speed option featuring “Thin Pins” which allow you to sight in 5 or less pins with bow speeds up to 450 fps and 6 or more pins with bow speeds of 400 fps – something I don’t think we’ll have to worry about for a few years!

Continue Reading

Click to comment

ATA Trade Show

NAP Introduces the Killzone 2-blade Broadhead

Published

on

One of the newest additions to New Archery Products’ (NAP) family of broadheads is the Killzone. The Killzone is a rear-deploying 2-blade broadhead with a 2″ cutting diameter. New technology allows both blades to open and work together in unison for increased reliability. Another advantage of this design is that it allows the broadhead to gain maximum penetration while avoiding any single blade deployment or deflection upon impact or during penetration of the cavity.

With no o-rings or rubber bands to hold the blades in place bowhunters don’t have to worry about the blades prematurely opening. The rear-deployment design is also the least restrictive when it comes to penetration which means it doesn’t rob much of the arrow’s energy upon impact. Two blades also require less energy to push through an animal than 3 or 4 blade broadheads.
The blades on the Killzone feature NAP’s Diamized blade technology which NAP claims is one of the sharpest blades in the industry. Another thing that bowhunters in states like New York will appreciate is that the blades on the Killzone fold back, so it is not a barbed broadhead and is legal in most states including states like New York where barbed broadheads are illegal.
The Killzone is a 100 grain broadhead and available in three models: Cut-On-Contact tip, Trophy Tip or Deep Six. Sold in a 3-pack, the Killzone also includes a practice head that is designed to be easily removed from your target and will not tear it up as the real broadhead would.
The Killzone is set to retail for $39.99. A 3-pack of replaceable blades and tips will also be available. The blades are easily replaced and come with blades, replacement screws and wrench. Practice heads are also sold separately and will be in a 1 pack for $9.99.

Continue Reading

ATA Trade Show

Muzzy Introduces New DX-3 Broadhead

Published

on

I’m really excited about Easton’s new Injexion arrows with the smallest diameter of any hunting arrow on the market (just .236 compared to .294 for a standard diameter carbon arrow). The smaller diameter arrow shaft allows for increased penetration and decreased wind drift. The smaller diameter arrow, however, required Easton to develop the Deep Six insert.

Deep Six inserts, which use a non-conventional thread pattern (40 threads per inch instead of 32 threads per inch), provide 25% more thread engagement to keep points secure inside the insert. Additionally, the inserts are made from stainless-steel instead of aluminum for a 25% increase in strength. It also means your standard broadheads won’t work with the new Deep Six inserts and only specially designed broadheads will work. One such broadhead is the new Muzzy DX-3.
I had a chance to stop by the Muzzy booth at the ATA Trade Show and get my hands on a DX-3. Speaking with the guys in the booth I learned just how painstaking of a process developing the new DX-3 was – moving 1/10 of a grain from one end of the broadhead to another while still maintaining the 100g final weight was no easy feat.
The DX-3 is in essence a modified MX-3 with a slightly thicker ferrule and a tapered end to meet the shaft diameter for less friction and drag during flight. The same .025″ blades found on the MX-3 are used on the new DX-3 which also has a cutting diameter of 1-1/4″.

The Muzzy DX-3, coupled with the Easton Deep Six System, produces less wind drag than other larger broadhead-arrow combinations, resulting in increased accuracy and deeper penetration. When the same amount of energy is concentrated in the smaller Deep Six/DX-3 package, the result is devastating. The DX-3 also fits Easton’s Axis and Full Metal Jacket with Deep Six inserts. The Muzzy DX-3 has an MSRP of $29.95.

I’m really looking forward to shooting the new DX-3 and comparing the penetration against a MX-3 on a standard shaft. I have a feeling there will be a very noticeable difference in penetration. Now I just need get my hands on some Easton Injexion shafts!

Continue Reading

ATA Trade Show

2012 Bowtech Insanity CPX and CPXL released at the ATA Trade Show

Published

on

Following on tradition, Bowtech once again unveiled it’s new flagship bow at this years ATA Trade Show in Columbus, Ohio.

Advertisements with the phrase “Contain the Insane” were showing up everywhere and fueled anticipation for the unveiling of Bowtech’s latest creation. At 9:00 am on January 10th it happened – the Bowtech Insanity was unveiled to an enthusiastic crowd on the showroom floor at the ATA Trade Show.

The Insanity comes in two versions, a 32″ model shooting 355 feet per second and a 35″ model shooting 340 feet per second.

Featured on the Insanity bows is Center Pivot Extreme Technology, which resists shooter induced torque for greater forgiveness and accuracy. The OverDrive Binary Cam System to eliminate cam lean issues and provide exceptional tuning to produce cleaner arrow flight for greater accuracy.

HardCore limbs boost efficiency for more speed without a harsh draw. On typical limbs, most of the bow’s energy is stored near the outside of the limb, while the core stores minimal energy and serves as little more than a spacer.

HardCore Limbs put the core to work, storing energy not only near the surfaces, but also inside the limb. By sharing the workload, stress is reduced, producing exceptional durability. The carbon core is also significantly lighter than other limb materials available today, which produces a tighter physical response for increased energy efficiency, less noise, and less vibration.

The FLX-Guard greatly reduces cable guard torque to produce better arrow flight and easier tuning for greater accuracy. As the archer draws back, the cable guard flexes inward absorbing the cable guard torque that would normally be transferred to the riser. This also reduces lateral nock travel which increases the tuneability, forgiveness and accuracy of the bow.

The Carbon Rod String Stop is made of carbon, an extremely strong material with vibration-dampening properties. It is positioned directly in line with the stabilizer to effectively transfer vibration from the string to the stabilizer. This optimizes bow balance and dissipates noise and vibration efficiently.

Both bows come standard in Mossy Oak Treestand. Alternative finishes include Mossy Oak Infinity, GORE Optifade Forest or Open Country, Realtree APG HD and BlackOps. Target colors AnoRock Onyx and Inferno area also available. All finished except Mossy Oak Treestand include black limbs.

The insanity CPXL has a longer axle-to-axle length for added stability and forgiveness, which makes it the perfect fit for archers with a draw length up to 32″. The Insanity CPX will have a suggested retail price of $999 and the CPXL will retail for $1,049.

I had a chance to shoot the Bowtech Insanity side by side with last year’s Invasion at the Bowtech shooting lane. Shooting the Insanity was exciting as the bow really put some heat behind the arrows as it sent them down range.

One thing that stood out to me when drawing the bow was the short valley. Upon releasing the arrow I felt a lingering vibration throughout the bow. However, this was a bare bow so some vibration is to be expected and a hunting rig outfitted with a stabilizer and other accessories should significantly decrease if not completely eliminate any vibration.

Another notable mention was the overall balance of the Insanity. When shooting last year’s Invasion, the bow slightly kicked back after the shot. The new design of the Bowtech Insanity makes the bow extremely well balanced and the Insanity remained steady even after the shot.

Overall, I think Bowtech did a good job with the Insanity and there were noticeable improvements over the Invasion, specifically in the overall balance of the bow. The bow was fast, the grip was slim and the bow was easy to keep on target. The valley was short, however, and I did have one draw where I let up a little while at full draw and the bow pulled me forward.

If you have a chance, take a trip to your local Bowtech dealer and shoot the Insanity to see what it’s all about.

SPECIFICATIONS
CPX
Brace Height: 6″
Draw Weights: 50, 60, 70, 80
Draw Length: 25.5-30 inches
Axle to Axle: 32″
IBO/ATA Speed: 355 fps
Kinetic Energy: 98.0 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $999
CPXL
Brace Height: 7″
Draw Weights: 50, 60, 70, 80
Draw Length: 27.5-32 inches
Axle to Axle: 35″
IBO/ATA Speed: 340 fps
Kinetic Energy: 89.9 ft.-lbs. at 70 lbs.
Effective Let-Off: approx 80%
MSRP: $1,049

Continue Reading

Trending